The Retirement Spending Insight is designed to show clients the maximum they could spend, once in retirement, to spend down their available liquid assets to near zero by the end of the plan. This is exclusive of illiquid assets, (usually properties) and accounts that have been ring-fenced – those excluded from being a potential payment source, due to withdrawal limits.
If you would like to watch a short video on the Retirement Spending Insight - click this link Retirement Spending Insight video - UK or continue through this article for further information on this Insight.
Tip: Planned Withdrawals are also honoured within the Retirement Spending Insight results. This could mean that the Retirement Spending results are lower than expected, due to the Planned Withdrawals.
Setting up a What-if and removing any exclusions, such as Withdrawal Limits and Planned Withdrawals, will provide you with a much clearer picture of the Retirement Spending expense.
To find this annual expenditure, the Retirement Spending Insight creates a “Spending Analysis Expense”. Think of this as any other expense where the value is a present amount, which is inflated using the default inflation rate in Plan Settings.
This Spending Analysis Expense is applicable after retirement. The analyser will attempt to fulfil this maximum Spending Analysis, plus any mandatory expenses (such as debt payments, any ongoing adviser charges set up and any premiums on protection policies).
All non-mandatory expenses are dropped from the simulation in the years after the retirement event. Note this includes one-off Milestone expenses.
The system then does a binary solve to determine the maximum Spending Analysis Expense value (in today’s terms) that can be fulfilled, so that available liquid assets are spent down over the course of retirement, and there is no resulting shortfall in the plan. This is not necessarily a “spend to zero” solution, as some accounts may have withdrawal limits set, and the simulation will honour these restrictions.
See Expense details by clicking on Year View top right, shown below, or double clicking on a bar of the chart. Exit this detailed view by clicking on the Year View Icon again.
NOTE: the Spending Analysis Expense figure returned is in today's terms. This figure is escalated from the start of the plan, using the default inflation rate in plan settings.
Additional Details
By default, the Insight currently uses the Principal client's retirement event, or it uses the start of the plan if the primary client is already in retirement and no retirement event is found.
If the second client has already retired, the simulation will still calculate from the primary client’s retirement event.
Debt and future asset purchase expenses remain in the plan unmodified, as well as any other expenses that are the result of other entries in the plan, such as insurance premiums and linked expenses. Future asset purchases, Planned Contributions and taxes also remain in the plan. All other “user entered” expenses are modified, to end at the retirement event.
The value calculated and shown as the result is the maximum retirement spending capacity (present value). The bar in the chart is the future value of the spending capacity result and the sum of the mandatory expenses in the year (debt, etc.) as shown above.
The spending level is assumed to continue until the end of the plan, with inflation. If the plan is for a couple, it continues until second death.
The maximum retirement spending amount is a value determined by examining the entire period of retirement until mortality. The figure is in today’s terms, and can be inclusive of taxes or net of taxes. The simulation uses a binary solve algorithm, to find the maximum value of the spending goal expense such that there will be no shortfalls throughout the entire planning horizon, after the retirement event (or start event if no retirement event).
Essentially, the calculation is working out how much can be taken out of the plan per year, to end up with zero liquid assets (excluding any that have withdrawal limits set) at the end of the plan (minus any mandatory expenses that must be fulfilled). In most plans, this will correspond to the spending amount that results in zero liquid assets at the end of the plan. However, the simulation doesn’t actually inspect the account values, but instead looks at the shortfall during each iteration of the solution algorithm.
Note for Reports
The Report value will use the Event and settings (i.e. Including/Excluding Taxes) used in the Insight when last run in the software - or defaults to the Retirement event, as explained below. For example, run the Insight from Mr's Retirement Event, Excluding Taxes and that will be the value shown in the report. Run from Mrs' Retirement Event, Including Taxes in the software and that is the value it will show in the next report. This means you can produce a report for the Event and settings used in the software.